Home / Products / Spray booths

Spray booths

Our combined spray/drying booths are manufactured for industrial applications and for the automotive industry

The spray/drying booths meet all requirements for priming and finishing as well as for water and solvent based painting.

Spray booths must comply to a wide range of specific regulations including i.e. fire, ATEX, working environment and safety for machinery. Furthermore, when buying a paint facility from Ventherm, you can expect quality and reliability to be on top and the energy consumption to be low.

Iindustrial applications

Single spray and drying booth

Performed in non-combustable materials. Local authorities might require it erected in a separate fire section within the building.
Performed according to EN 16985 / EN 1539.
Air velocity 0,3 m/sec. vertically in empty booth. Air volume can be reduced if painting only items larger than 6 m.
Air injection in the entire ceiling through filters, which creates counter pressure and ensures an even injection throughout the entire booth.
Extraction in the floor – as close to the items as possible.
Paint-stop is placed under gratings in the floor.
Illumination min. 750 lux according to EN 16985.
ATEX zone 2 classification calculated according to EN 16985.

Double spray and drying booth with intermediate roller door

Same requirements as for single spray booths – see above.

Constructed like 2 independent booths – only separated by an intermediate roller door in full width and height.
Thereby, maximal flexibility and the possibility of painting large as well as small items in an economically responsible way are obtained.
When the intermediate door is open, the booths will automatically run as one large booth.
When the intermediate door is closed, the two spray/drying booths can run independently.

Extraction in the wall

In some countries it is accepted to extract paint dust in the lower part of the wall instead of extracting it through the floor.

Excavation and casting of extraction pits in the floor can sometimes be unreasonably costly, or even close to impossible to establish.

Therefore some countries accept extraction in the wall, although the required vertical (down draft) airflow cannot be ignored, and the intended and best way of performing it is through the floor.

Extraction in the wall often leads to a slightly poorer working environment for the operators since paint dust is extracted behind the operator and hense dragged towards him and his brea- thing zone – a fundamental issue that ought to be awoided in all paint operations.

Extraction in the wall often requires significantly more ducting for the installation.

Outdoor spraybooths for painting or blasting

If a customer doesn’t have sufficient space available for new paint facilities inside existing premises, Ventherm’s outdoor concept is often a very attractive solution. Ventherm can build spray booths and blast rooms as a selfcontained outdoor building, which is much cheaper than erecting a new building and subsequently installing booths inside the new building.

Ventherm’s outdoor booths are designed after all applicable standards for i.e. snow load and wind load etc., and obviously the booths are fully insulated and waterproof. The outdoor booths are available in a wide range of colors. Thus, they can look like our customer’s existing building design if required.

Horizontal ventilation

In some countries it is accepted to extract paint dust in the lower part of the wall instead of extracting it through the floor.

Excavation and casting of extraction pits in the floor can sometimes be unreasonably costly, or even close to impossible to establish.

Therefore some countries accept extraction in the wall, although the required vertical (down draft) airflow cannot be ignored, and the intended and best way of performing it is through the floor.

Extraction in the wall often requires significantly more ducting for the installation.

Elevate your painting with Industrial paint booths

At Ventherm, we understand the critical role that a reliable and efficient paint booth plays in industrial painting. Our range of industrial paint booths is designed to meet the diverse needs of the sector, providing unparalleled precision, durability, and performance.

We recognize that every industrial painting project is unique. That’s why we offer customized paint booth solutions to fit your specific requirements. Whether you’re dealing with large machinery, automotive components, or other parts, Ventherm has the right solution for you.

Ventherm Catalogue

Looking for further information? Please read Ventherm’s catalogue for product designs, company merits, and specifications for use and implementation.

Catalogue 2023

English

Katalog 2023

Dansk

Katalog 2023 Svenska

Svenska

Katalog 2023 Deutsch

Deutsch

Catalogar 2023 Español

Español

Catalogue 2023 Français

Français

Further information

If you want to know more about Ventherm´s industrial solutions, or see selected references, you are most welcome to contact us or click on to see our cases categorized by industries. You can also visit the contact page to get an overview of our worldwide network of local distributors.

Spray booths

Our combined spray/drying booths are manufactured for industrial applications and for the automotive industry

Iindustrial applications

Single spray and drying booth

Double spray and drying booth with intermediate roller door

Extraction in the wall

Outdoor spraybooths for painting or blasting

Horizontal ventilation

Elevate your painting with Industrial paint booths

Ventherm Catalogue

Further information

Company

Office hours

Follow us

Global distributers

Cases

Environmental policy

Products

Quality management

Environmental policy